6sp battery front
Battery for iPhone 6S Plus
Battery for iPhone 6S Plus
Battery for iPhone 6S Plus
Battery for iPhone 6S Plus
  • Load image into Gallery viewer, 6sp battery front
  • Load image into Gallery viewer, Battery for iPhone 6S Plus
  • Load image into Gallery viewer, Battery for iPhone 6S Plus
  • Load image into Gallery viewer, Battery for iPhone 6S Plus
  • Load image into Gallery viewer, Battery for iPhone 6S Plus

Battery for iPhone 6S Plus

Regular price
$20.00
Sale price
$20.00
Regular price
Sold out
Unit price
per 

Battery for iPhone 6S Plus
For Models: iPhone 6S Plus


Package includes:

  • 1 x Battery
  • 1 x Adhesive strip
  • 1 x tool kit


6 months warranty

iPhone 6S Plus Battery Replacement


Seek professionals

42

Steps

1

Hour

Step 1

Switch off your iPhone 

Remove the 2 screws as shown in the image

• 2 x 3.4 mm screws

Step 2

Apply heat to the lower edge of the iPhone using a hairdryer to soften the adhesive securing the display assembly.

Do it for about a few minutes.

Step 3

If your display screen is badly cracked, you can prevent further breakage of the screen by taping it over with a clear tape.

Place the suction cup on the screen of your iPhone, just slightly above the home button.

Make sure that the suction cup is pressed securely to ensure a tight seal.

Step 4

Using an opening tool, pull the suction cup while holding the phone down to slightly separate the front panel to create an opening. 

Once you get an opening, continue to pry the rear case down and away from the display assembly while pulling up with the suction cup.

If you are still having trouble, heat up the lower edge of the phone again until it is too hot to touch.

Step 5

Use the opening tool to create an opening between the screen and rear case, and twist it to widen the gap.

Do it for the left side of the phone, between the display assembly and rear case and slide it up to separate the adhesive and pop the clips free.

Now slide it to the right side of the phone to separate the adhesive and pop open the display clips.

Step 6

Pull and remove the suction cup from the display assembly.

Step 7

Lift the screen up from the home button, using the top as a hinge.

Step 8

Remove the 2 screws shown in the image.

• 1 x 2.3 mm screw

• 1 x 2.9 mm screw

Step 9

Remove the metal battery connector bracket.

Step 10

Using the opening tool, pry the battery connector up from its socket away from the logic board until it stays separated.

This is to avoid any accidental connection to the battery.

Step 11

Remove the screws as shown in the image

• 3 x 1.3 mm screws 

• 1 x 1.6 mm screw

• 1 x 3.0 mm screw

Take note that the middle 1.3 mm screw may be under the sticker label if you don't see it.

Step 12

Remove the front panel assembly cable bracket from the logic board.

Step 13

Using a spudger / your nail, disconnect the front-facing camera and sensor cable.

Take note, for the next 2 steps, pry up only on the cable connectors, and not on the sockets of the logic board.

Step 14

Using the flat end of the spudger, disconnect the digitizer cable connector.

Step 15

Using a spudger / your nail, disconnect the home button cable.

Step 16

Separate by removing the front panel assembly from the rear case.

Step 17

Using the tweezers, peel back the battery adhesive tab as shown in the image.

Be careful during this step as puncturing the battery can release dangerous chemicals.

Step 18

Slowly pull the adhesive tab away from the battery.

Pull the strip steadily at a low angle and maintain constant tension on the strip until it slips out from between the battery and the rear case.

If the strip breaks, carefully retrieve it with the tweezers without damaging the battery and continue pulling the strip.

If the strip breaks off underneath the battery and can't be retrieved, continue with the steps below.

Step 19

Skip to step 22 if you have removed both adhesive strips successfully.

If any of the adhesive strips broke off and the battery remains stuck to the rear case, use a hair dryer to heat the rear case directly behind the battery. It should be slightly too hot to touch comfortably.

Step 20

Flip the iPhone back over and thread a piece of dental floss or strong string behind the battery. Then, slowly pull back and forth in a sawing motion to separate the adhesive.

Alternatively, you can insert a plastic card between the case side of the battery and the rear case. Press the card further in to break up the adhesive behind the battery.

Step 21

Remove the battery from the iPhone.

If your replacement battery came in a plastic sleeve, remove the sleeve before installation by pulling it away from the ribbon cable.

Step 22

Remove the small plastic films covering the flat ends of the adhesive strips.

Step 23

With the battery facing up (the battery connector is on the right side), align the exposed portion of the adhesive strips along the lower edge of the front of the battery, and press them into place.

Step 24

Turn the battery around.

Starting from the lower edge, peel off the blue film.

Step 25

Roll the adhesive strips over the bottom edge of the battery and lay the strips down flat to stick to the back.

Press the strips firmly into place along the back of the battery.

Step 26

Peel away the pink strip of film to expose the adhesive strips.

Step 27

Without sticking the battery down, lower the connector into the iPhone and align it to its socket on the logic board.

Step 28

 Connect the battery.

Step 29

Carefully position the battery and set it down into the iPhone.

When the battery is correctly positioned, lay it down in the iPhone and press it firmly into place to allow the adhesive strips to stick to the rear case.

Step 30

Disconnect the battery again before reassembling your iPhone as it can destroy sensitive components.

Step 31

Bring the front panel assembly and rear case together.

Step 32

Using your finger/ opening tool, connect the home button cable back to the logic board.

Step 33

Using your finger/ opening tool, connect the digitizer cable connector.

Reminder! Do not press the center of the connector. Press one end of the connector and then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage.

Step 34

Using your finger, connect the front-facing camera and sensor cable connector.

Step 35

Place the front panel assembly cable bracket back onto the logic board.

Step 36

Screw back the screws as shown in the image.

• 3 x 1.3 mm screws 

• 1 x 1.6 mm screw

• 1 x 3.0 mm screw

Incorrect placement of the screws may result in permanent damage to the logic board.

Step 37

Use your finger/opening tool to insert the battery connector back to its socket on the logic board.

Step 38

Insert the metal battery connector back into the bracket.

Step 39

Screw back the screws as shown in the image 

• 1 x 2.3 mm screw

• 1 x 2.9 mm screw

Step 40

Lift the screen down, using the top as a hinge.

Close the phone.

Step 41

Screw back the 2 screws as shown in the image.

• 2 x 3.4 mm screws

Step 42

Perform a hard reset after reassembly to prevent issues and simplify troubleshooting.

1. Press and hold the Home button.

2. While holding the Home button, press and hold the Sleep/Wake button.

3. Continue holding both buttons for about 10 seconds, until the Apple logo appears.

troubleshooting


When reassembling your phone, the display data cable may pop off its connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.